Last Updated on
It’s nice to end the day by spending quality time in your outdoor living space. But for you to fully enjoy the experience you need a comfortable and stylish chair. The best option is an Adirondack chair.
Made from recycled pallets, this Adirondack chair will give you a comfortable place to relax and unwind in your outdoor area without breaking the bank.
You can build a couple of these for your friends and relatives when they come to visit. Not only do you get great seating for your outdoor area, you also learn new skills, and help lessen the garbage in our environment.
How many of these do you need?
Click on any image to start lightbox display. Use your Esc key to close the lightbox. ?
- 3-4 good Pallets
- Wood Putty
- Bolts, Nuts, Washers
- Wood Glue
- Small Bit – for pilot holes, size depends on the screws you use
- 3/8″ Spade/Forstner Bit – for counter sinks
- Circular Saw
- Reciprocating Saw
- Power Drills Screw Driver
- Router (optional)
Pallets aren’t easy to take apart. They’re also usually not made of very good lumber. If you use them for projects, you’re going to spend A LOT of time dismantling them and you’re not going to get much from a single pallet.
Working with power tools is dangerous, doubly so when working with pallets. There are hidden nails, knots, warped boards, etc. Use proper safety equipment, especially eye protection. Don’t use a power tool unless you’re familiar with it.
I start by cutting off the outside stringers (the 2×4’s) with a skill saw. Watch out for nails! Draw a straight line on each side as a guide to cut off the outside stringers. A chalk line works well. You’ll want to set your depth at a fraction more than the 3/4 inch board. After you cut along each outside stringer (not the middle!), flip the pallet over and do the same on the other side.
Pallets are usually made of the lumber that got rejected for other uses. It’s hard, often warped, has old broken nails embedded in it, and generally is just a pain to work with. Be careful. Wear goggles. Repetitive work breeds carelessness.
Some other methods: Cut the nails with a sawzall. Use a pneumatic chisel. Use a catspaw to dig the nails out (for certain pallets, this is easy. For some, it’s darn near impossible.) Use a hammer to knock the stinger off if it’s stubborn.
You’ll be left with a bunch of 1X4’s and 1X6’s attached to the 2×4 in the center. By rocking the 1×4’s and the 1×6’s back and forth, you can get the board off without totally destroying it. There will still be quite a few ruined boards. Good for the woodstove.
Pull or remove any nails left in the board and stack it to the side. You may also want to grade your boards, based on knots, warping, bark, etc. This will help later when you try to decide what to use for what job.
I usually get about (6) good 1×4’s and (3) good 1×6’s per pallet. I also get a (3) 4′ lengths of 2×4.
Using a 35″ 1×6, draw a grid of one inch blocks like the picture below. Keep in mind that the lumber is only 5.5″ wide. you”ll end up with a course of 1/2″ blocks at the top. Using the blocks, one at a time, draw the pattern. You’ll need two and you can use the first to trace out the second.
REMEMBER! If one side of the board is better than the other, to cut accordingly. In other words, the stringers should be mirror (opposite) copies. Pallet wood usually has both a smooth and a rough side.
Using a 21.5″ 1×4, draw a grid of one inch blocks like the picture below. Keep in mind that the lumber is only 3.5″ wide. you”ll end up with a course of 1/2″ blocks at the top. Using the blocks, one at a time, draw the pattern.
Using a 22″ 1×4, draw a grid of one inch blocks like the picture below. Keep in mind that the lumber is only 3.5″ wide. you”ll end up with a course of 1/2″ blocks at the top. Using the blocks, one at a time, draw the pattern. Cut out (2) armrest brackets. Use the measurements below.
Continued Page 2…