Build a wishing well burn barrel from an old washing machine drum

2
19826
Wishing Well Burn Barrel

Why buy an expensive, decorative fire pit for your yard when you can have something as impressive by upcycling an old (cheap) washing machine drum? Take a look at this wishing well!

Wishing Well Burn Barrel

This DIY fire pit is another example of creativity, function and beauty. And what’s great about it is that it is also simple, making it easy to make, assemble and use!

The wishing well design does not only provide good fire, you can also conveniently use it to cook or heat foil-packed food like vegetables and meat. Just put your meal inside the metal bucket, lower it down and crank it up again when it’s done! If you want to boil water, you can replace the bucket with a camping kettle.

As mentioned, this creative fire pit is very easy to assemble. You only need 8 bolts and 10 minutes, and you’ll be ready to enjoy some outdoor unwinding! Want to use this burn barrel in your backyard, or bring it at the beach or for camping? Why not? All of its parts fit inside the washing machine drum, so you can easily transport it to anywhere you wish. :)

Got access to an old washing machine drum? Read on to see what else you’ll need to make your own version of this wishing well burn barrel!

Click on any image to start lightbox display. Use your Esc key to close the lightbox. 8-)

Materials:

  • Old Washing Machine Drum
  • 4 sheets of 24in x 6.5in Perforated Steel
  • 5 ft long of 3/8in Mild Steel Rod
  • 12 pieces of 1in x 4in x 1/8in Bar Stock Metal
  • 2 pieces of 2in x 24in x 1/8in Bar Stock Metal
  • 4 pieces of 9in long, 1in Angle Iron
  • Permanent Marker
  • Paper
  • Hinges
  • Steel Chain
  • Threaded Quick Link
  • #6 and #8 Bolts with Nuts

Tools:

  • Power Drill with bits for metal drilling
  • Welding Machine
  • Tape Measure
  • Metal/Steel Cutter
  • Clamps
  • Vice Grip

Steps:

First things first, you need a barrel!

Washing machine drums are easy to come by if you look for abandoned machines out on curbs, scrap yards, or you might be looking to find a use for your own worn out washing machine.

Be prepared to get a little dirty wrestling it out but it’s worth the fight. You will probably end up smelling a bit like laundry soap by the end.

Wishing Well Burn Barrel

I used some perforated steel for the roof. The holes will make it light, prevents it from trapping heat, and allows you to watch the fire from the top.

The sheets I used were scrap from the shop so I’m not sure of the guage of the metal but it was a total of 4 sheets that were 24in x 6.5in.

Wishing Well Burn BarrelI overlapped the metal sheets a bit to make it look like traditional wood slats and screwed them together. 2 screws per roof half was enough to hold it together well. #6 bolts can be found at any hardware store and they fit the holes perfectly.

Wishing Well Burn BarrelI chose a set of decorative hinges and screwed those in with the same #6 bolts. I used hinges so the roof can be lifted out of the way with a handle I welded on. That way you can have easy access to add wood, poke the fire, and handle the bucket without struggling.

Wishing Well Burn Barrel

For the hot handle I cut apart a chipping hammer, sandblasted it, and spot welded it onto the roof that will lift (opposite side of the turn handle so they don’t collide). Tah Dah!

Now let’s build the crank for the bucket…

Continued Page 2…

  • Peta Janine

    They are some of the best fire pits ever!

  • Carey Thomson

    These make the greatest fire pits! I need one!